공지사항

How to Replace a Kia Sportage Replacement Key

For a variety of kia key replacement models keys, the key has a built-in keyless entry system. This key usually resembles the remote control and can be changed with a new one from a Kia dealer or Kia Replacement Key Fob a locksmith.

Key fobs can stop working for a variety of reasons, such as batteries that are dead worn buttons or buttons, signal interference, water damage and a damaged receiver module. Here are some helpful tips to assist you in getting your Kia key fob that is a replacement for the sportage for good.

How do you replace the remote key or smart key?

Whether your Kia comes with an intelligent key, remote key push to start key or a regular non-transponder metal key, the battery in these keys will eventually need replacement. This is especially relevant if your car displays a message that the smart or remote key has a low battery.

It's a fairly simple procedure. To replace the battery on the key fob remove the mechanical key from the slit at the back of the key fob. Then break the cover. Inside the key fob, there will be a small screw that holds the battery in the correct position. By using a small screwdriver remove the screw and remove the old battery. Insert the new battery and close the slit on the key fob.

When the key fob is equipped with an updated battery, test it by pressing the locks and unlock buttons. If the doors lock and unlock exactly as you expect, then you're in good shape! You can now make use of Kia's hands-free lock/unlock function when your fingers start to get cold or you have to run some errands in Brandon.

Note: Some key fobs could need to be programmed (transponder chips or smart keys). This requires a particular programming machine that only the dealer or locksmith has access to. Other keys (non-transponder metal keys) do not require programming. If your key has to be programmed, you will need to be aware of the key code written on the tag that identifies the key and record the number in a secure place.

How to replace a battery

If the kia replacement key fob (xdpascal.com) key fob is unable to respond to pressing the lock/unlock button, it's likely that the battery is low. A low battery may cause other issues, like the check engine light coming on or the engine not cranking correctly. Fortunately replacing the battery on the key fob is a simple DIY project that requires just a few tools.

Before you begin ensure that your vehicle is off and all doors are closed. Find the small, metal or plastic piece near the bottom of the key fob. Move it until the key comes out. Then, you can insert the key in the door handle of the driver to unlock your car.

To replace the battery on the key fob, take off the rear cover. Make use of a plastic pry tool to open the latch that holds the black negative cable. Remove the old battery and then orient the replacement battery so that its "+" side is facing you and the "-" negative side is facing the fob's electrical contacts. Push the new CR2032 battery straight into position without putting too much force on it to avoid bending or damaging the contacts of the metal.

After installing the new battery then turn the key fob off and on in the ignition until the door locks cycle. You can then test your kia ceed replacement key's keys fob again to confirm that it's working properly.

How to replace the smart key?

You could have an ordinary keyfob or Smart Key depending on the model of kia picanto key fob replacement Sportage. The smart key features an embedded mechanical key blade, unlike the standard key fob, which does not. Both types of key fobs have an internal battery that will eventually have to be replaced. It is a simple process which takes just two minutes.

Make sure you turn off your Kia and sit on a flat, well-lit surface before you begin. Also, keep in mind that there are tiny parts inside the fob that could be removed if not vigilant.

The first step is to find the small release button that is located on the backside of the fob. It will be either a circular silver button or a rectangular slot. When you press it the mechanical key blade will be released and Kia Replacement Key Fob you can then open the key fob.

After the key fob has been opened, take out the battery that was in it. The new battery is a CR-2032, and can be bought online or in your local auto parts shop. Once you're done it should be possible to lock and unlock your car with your key fob, even if your engine isn't running!

How do I replace the mechanical key?

The Kia key fob is an amazing option that lets us lock and unlock our car at the click of a button. However, like all devices there are issues with it from time to time. Luckily, there are methods to resolve these issues and keep our key fobs in good working condition for the long term.

A low or dead battery is one of the most common problems. This can cause the fob to cease working or to work intermittently. If this is the case, try replacing the battery with a fresh new one.

If this doesn't solve the problem, use the flathead screwdriver that is standard to push the fob's casing made of plastic open. Be cautious not to damage any internal components or scratch the plastic. Once the battery is opened, carefully remove the old battery and replace it with a brand new one.

Close and open the door using the mechanical key. (Every kia fob comes with an emergency mechanical key that fits into the slot). Test the fob to make sure it's functioning properly. Contact a dealer, or a locksmith to address the issue in the event that the fob is not working. To avoid future lockouts, ensure that you have an emergency key that can work on all door and trunk cylinders.