공지사항

Ignition Cylinder Lock Repair

The ignition cylinder lock allows the key to be turned, allowing the car to start. It operates through springs and chambers that may be damaged by environmental elements like low or high temperatures.

If your ignition lock repair switch or key won't turn, it could be a sign that the cylinder for your lock is damaged and must be replaced. This task should be left to an experienced auto locksmith.

Remove the Steering Column Covers

Ignition lock-cylinders are mechanical components that allow a key into the ignition switch to be turned to start the vehicle. They can be damaged and fail due to various reasons, such as when the key is put in too strongly or in the wrong place. They can also degrade and fail due to corrosion or any other reason. It's time to replace your ignition cylinder if it's not working. You can do this yourself, but it's a job which requires you to remove the covers on the steering column and the airbag cover. The process is risky and could be difficult. It may also require specialized tools for the replacement cylinder.

The ignition cylinder is in the middle of the column, where the steering wheel attaches. It has two screws at the bottom and an attachment clip on the side to secure it to the column. Take these screws off prior to working on the cylinder to stop it from falling out and getting lost.

After you have the screws removed, you can remove the plastic retainers off the bottom of the cover. A metal retainer clip into the top cover to hold it in the right place. It is possible to remove the cover off of the steering wheel in order to remove the tabs on the lower part of the plastic.

The tabs can be ripped off by taking out one of the retaining screws, and then bending the tab a bit. If the tab has been broken completely, you can replace it by using a piece of perforated metal strapping available at most hardware stores. You'll need U-clips for attaching the new "tab" to the bottom. They can be bought at any auto parts shop.

Once the plastic tabs have been removed and the airbag cover is pulled back, you can access the hole for the ignition cylinder. With the 1/16-inch allen wrench you can unlock the ignition lock and push it onto the cylinder retaining pin. Then, you can remove the cylinder. It may be necessary to replace it with a specially designed cylinder for an anti-theft system.

Remove the Ignition Cylinder

Although a majority of vehicles now have push-to-start, there remain some vehicles on the market that require an ignition lock. This cylinder, which is mechanical, is contained in the electrically powered component known as the "ignition switch" that is used to lock the ignition and "reads the anti-theft code within the car key ignition replacement before allowing it to turn on.

If your car is showing signs of a failing ignition lock cylinder, it may be time to call an auto locksmith for assistance. A faulty cylinder can cause several problems, including a lack of power from the engine as well as problems with inserting and taking out the key. Keys that are damaged by wear can cause damage to wafer tumblers, which allow the ignition cylinder to turn. This can cause a jam and prevents the vehicle from starting.

Depending on the model and the make the cover for your ignition switch can be secured with clips or screws. Utilizing a screwdriver to loosen the screw and slide off the cover to expose the cylinder that locks the ignition. This is typically a metal cylinder approximately the size of the size of a quarter.

To remove the cylinder you'll have to drill out the pin that holds it in place. Use a drill bit slightly larger than the slot for the key and then drill straight into it until the cylinder breaks free. You'll then be able remove the cylinder and replace it with a new.

You'll need to refer to your service manual to find out the specific steps to remove the ignition cylinder. Once the cylinder has been removed, you can put in the new ignition switch.

Before you can do this, you'll need to reinstall the steering column covers. Also, you'll need to tighten two screws on top of the lock assembly that secure it. After you've done that, installing your new ignition cylinder shouldn't prove to be too difficult.

Take out the Ignition Switch

The ignition switch and cylinder lock are two distinct components of the electrical system in your car. Although they might appear like they are, they can be replaced or repaired independently of one another. The switch is electrical and supplies energy to your vehicle. The cylinder is a mechanical tumbler which your key can slide into. You can tell if the ignition cylinder has failed by its inability to turn the key.

When the cylinder fails and the pins inside the tumbler could wear out which makes it difficult or impossible to insert or pull out your key. If you notice your key is deteriorating and won't turn it is recommended to have the wafers inside it replaced or smoothed out by an expert locksmith.

Based on the make of your vehicle, there may be a bolt or screw that holds the switch in place and removing it will expose the ignition cylinder. It's important to consult the manual for your vehicle before trying this at home, because it could be risky and cause damage to the steering column as well as the plastic covers. Additionally the switch is linked with airbags' wires and any interference with this could result in serious injury.

To take the ignition cylinder out you'll need drills to loosen it. You can also use pliers remove it from the assembly however, this is typically more difficult than using the screwdriver. Once the ignition cylinder is loose it is possible to replace it with a brand new one from your local auto store.

You'll require all the wires connected to the electrical connector on the steering column in order to test its operation. It's usually easiest to disconnect the battery first, then take the key from the ignition and start the engine. Once the ignition is working it's time to reconnect the battery and test it again. If the vehicle still won't turn on, you will require that the immobilizer reset. This can be accomplished by a dealer or automotive service technician. This can be a complex procedure, and is better left to a certified professional.

Install the Ignition Cylinder

The ignition switch in your car sends does a new ignition switch require a new key signal telling the engine it's time for it to start. The key is inserted into a lock cylinder to trigger this process, but the pins and wafers inside the cylinder can wear down over time. This could make it difficult to turn on your car, or even impossible if the cylinder gets stuck.

If your key won't turn on the ignition, it is likely that it's due to needing to be replaced. A professional locksmith can replace the cylinder with a new one, meaning the new key will work with the old ignition switch, and will be capable of triggering the engine startup signal.

To remove the old lock cylinder, push in on the release pin on the bottom of the assembly and remove the cylinder from its housing. If the cylinder won't slide out, try pushing on the release pin again or using a screwdriver, you can press a small anti-rotation button beneath the face of the cylinder. You can also try pushing in on the cylinder with your key while turning it to the ACC or accessory position to see if you can force it out.

Install the new cylinder and test it by turning off the vehicle. If it is, you can reconnect the trim pieces you removed to access the cylinder. Then you can perform the relearning process to connect the new keys.

The ignition cylinder lock may not be as important to the functioning of your car as it used to be, but there are still instances when it is necessary to replace it. Talk to a professional such as an automotive dealer or locksmith to ensure that the task is done without causing damage to the steering column or other parts of your vehicle. It is crucial to ensure that the new ignition is properly coded to ensure that your car recognizes it as a genuine key. In the majority of cases this will require a dealer or other professional to carry out the relearn.