공지사항

Peugeot 208 Key Replacement

Peugeot 208 key replacement is best left to auto locksmiths with experience who have the appropriate equipment and know-how. They can make and program new keys much quicker than a dealership and at a cheaper cost.

A dead coin battery is most likely to be at fault the reason your key-fob stops locking or unlocking the doors. There are many other reasons why the key may be malfunctioning.

Dead Coin Battery

A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also hindering it from starting the engine. If this is the situation, you'll need apply the backup starting technique which is explained in the owner's manual of your vehicle.

Another reason why your 208 may not start is that the spark plugs have worn down. Spark plugs are what ignite the fuel to start the engine. They have a limited life span. They'll eventually break down if they aren't used frequently enough.

Fortunately, there's an easy solution for this problem. The best way to solve this issue is to determine the voltage of your car battery with a multimeter. If the voltage is below 11,5 volts then it's time to replace it. If the battery is damaged it is necessary to clean its contacts. You can do this by lifting the rubber covers that cover both battery terminals and using wire brushes to clean any corroded areas of the battery. You should then reconnect the cables that connect the positive and negative poles.

Water Damage

If your 208 isn't starting and the battery is not flat, then you need to make sure that the spark plugs are in good working order. It is possible that they're dirty, which causes them not to spark. This can be easily corrected by cleaning the spark plugs in an workshop.

Peugeot cars use a key with a transponder compatible with the immobiliser. This ensures that only the right key can start the engine. If the chip inside the Peugeot key is damaged, then it will not transmit the correct signal to the vehicle.

This is a frequent issue that can be caused by water damage. This is a common problem in warmer climates where the vehicle has been exposed to snow or rain. If this is the case, contact a reputable auto locksmith who has all the tools and equipment needed to modify the new key. They will also have all the latest technology and machinery needed to create the Peugeot smart key. The process shouldn't take longer than 15 minutes.

Contacts for the battery that are defective

Peugeot changed from the old carbon encased transponder chips to an entirely new kind of chip that utilizes electronic components on circuit boards. The new system is excellent when it's new, however the circuit boards wear out over time and cease to function properly.

This could stop the immobiliser from working, so your vehicle will not start. Contact a Peugeot specialist, or a locksmith, if this is the case.

A common issue occurs when the battery inside the key fob begins to die. This causes the blade of the key to stop feeding into the lock. A locksmith for cars will replace the battery, and then cut a fresh blade for you. This is a quick solution.

Faulty Receiver Module

If your Peugeot key fob isn't working after dropping it on the floor, getting exposed to a sudden downpour or accidentally washing it, it could be due a malfunctioning receiver module. The receiver module is responsible for transmitting radio frequency to the onboard computer that regulates the central locking system of your Peugeot vehicle.

The key fob itself has rubber seals that block water from getting to the electronic chip inside. Water can damage the chip if it is exposed to water for a long time. The high salt content in the ocean water or pool can cause damage to the key fob if it is submerged.

The module must be replaced if your Peugeot spare key is no longer working. This can only be performed by a professional auto locksmith or Peugeot specialist. peugeot boxer key fob programming keys, unlike other cars, are protected by an immobilizer system. This requires the right code to begin the car. It is for this reason that you should only trust an authorized Peugeot locksmith to design and program an alternative.

Computers with faulty on-board computers

The computer on the board of your Peugeot is responsible for many of the systems in your vehicle, from power windows to the airbags. When something goes wrong in these systems, it will typically display a code that identifies the problem. The code is stored within the system and will stay there until the problem has been resolved. This may require the on-board computers to be replaced.

One of the main causes of the airbag light coming on is loose or corroded connection in the airbag sensor. This could be due to wear and tear, ageing, or exposure to moisture and salt. It is crucial to get this issue resolved as soon as you can, as a malfunctioning airbag can be risky in the event of an accident.

If your Peugeot is showing a card not detected error then the key battery inside the key fob could be weak or dead. This will stop the key fob from sending a signal to disable the immobilizer on your vehicle. You can test this by pressing the unlock button on the key fob and then trying to start your car. If this doesn't work then the battery in the key must be replaced.