공지사항

UPVC Window Repairs

Upvc windows are energy efficient and can help to reduce heating bills. As they get older, however, issues can occur that need to be fixed. This can be due to damaged handles, hinges, or locks.

DIY people can fix wooden windows with ease. It's cheaper than buying a brand new window.

Cracks

Cracks and breaks can be a major problem. Leaving them unrepaired can cause water infiltration, less effective barriers against cold temperatures and the potential for structural damage. It is crucial to find a local repair or builder that specializes in the repair of uPVC frames and who has the experience, skills and equipment required to achieve the best results. This will ensure that the crack is repaired before it gets any worse and you don't have to replace the window glass or window unit.

There are many home-based remedies that can be used to repair small cracks in glass. Masking tape and superglue are two of the most common products to hold cracked glass in position for a short duration. For more severe cracks, the tape may need be extended on both sides.

Alternatively, two-part epoxy can be used to fix broken or cracked glass. Hardware stores typically sell this product for around $10. Make sure that your workspace is prepped before mixing the epoxy. Make sure you have the right equipment for the job, such as a soldering iron.

If your lower or upper sash is hard to raise it's most likely because the cords on the sash weights are damaged. This is a simple fix that can be accomplished with a ladder and flathead screwdriver. Replacing a rotted drip cap is another simple repair that is done at home. The drip caps that are not rot-free are readily available at many home centers and can be nailed or caulked into place with ease. Also, if you have a double glazed window repairs or triple-pane window, be sure to check that one of the panes are not broken. The reason for this is that the gases in the space between the windows are responsible for increasing the efficiency of the window. This should not escape.

Water Leaks

If your uPVC window is leaking, it can cause damage to your interior and result in costly repairs. Water leaks may also cause structural damage to your home as well as mold growth. It is crucial to address any problems caused by leaking windows right away to minimize the damage.

One common cause of window leaks is the damage to the sealant around the frame. Using silicone caulking can help improve the condition of the seal back to normal and stop water leakage. Examine for gaps and cracks around the window frame, as well as the brick or stone wall that surrounds your windows.

Another reason for leaky windows is the drainage hole is blocked or faulty flashing. Verify that the drainage holes have not been clogged or blocked, especially after a heavy downpour. Also, you should look at the flashing around your window to ensure that it's well-sealed.

Finally, it's essential to make sure that your drip cap isn't broken or rotten. A damaged or damaged drip cap could let water in the window from above and cause damage to your home's structure. Replacing a drip cap isn't difficult, and it's generally a simple process of purchasing the new one and nailing it into the correct position.

A professional can also check your windows for watertightness. They can employ a tool to determine your windows' water-tightness and ensure that they meet industry standards. If your windows fail the test, they will need to be replaced. This is a costly repair however it's worth it for the comfort and safety of your family.

Sagging

If your windows don't shut properly, it could lead to a number of issues, including drafts, condensation and a rise in energy bills. It could be an indication that the windows were not properly installed or the sealant is no longer effective. There are several things you can try to solve the issue.

The first step is to set up your workspace in a space that has plenty of light to repair your window in a timely manner. Start by laying down newspapers or an old blanket to shield the flooring from any splinters and drips from the windows while you work.

Use a white cloth that has been soaked in a solution of water and detergent. This will stop any stains of color appearing on your windows. If you're ready to work on your uPVC windows, begin by making note of where the hinge channel should be located. Unscrew the channel, and then fill the screw holes inside the frame using epoxy (for uPVC frames) or wood filler. Make sure you smooth the hole that you have filled before it sets.

Install the hinge channel after the holes are filled. Be sure to place it on the window jamb and drill the new screwholes about a quarter inch away from the original locations.

Next, measure the spindle protruding from the underside of your handle. You can either order an alternative or bring it to a shop selling hardware for a replacement. Then, pull out the setscrew on the shaft of the operator and file it flat so the set screw can be secured to the shaft (photo). Now, your uPVC window should be closing easily.

Broken Hinges

If your uPVC window hinges have been damaged or are not functioning correctly and you are unable to open or close the window, it will be difficult to open or close the window. This could cause a security problem and prevent your home from staying cool or warm. It's easy to get a new hinge for your uPVC windows. It is essential to select the correct type of hinge for your windows.

This is because the hinges have to be the same width to fit in the window frame. The most popular hinge for windows made of uPVC are standard 18mm or UPVC 15mm window hinges. There are also specialised hinges for wooden frames. Choosing the correct window hinge for your windows will aid in avoiding common issues that homeowners encounter with their windows, for example, not closing properly.

The hinges of your window could be stiff or loose for several reasons. The hinges may not have been tightened enough. You can check this using a screwdriver to locate the friction screw on the other side of the hinge and then loosen it. Then, you are able to adjust it by turning it either way until you achieve the desired result.

If your UPVC window hinges aren't working as they should, you can contact Preston Glass Fix for a quick repair. Our technicians will evaluate the condition of your hinges for your windows and provide you with the best solution for you. We can replace your window hinges, adjust them or install new locking mechanisms to ensure that your UPVC windows are secure and safe for a long time to come.

Locks that aren't working

UPVC window locks and mechanism are a very important part of the security of your home, they make it very difficult to open the window without breaking in. It can be a frustrating experience when a lock malfunctions, but you don't have to replace the entire window.

It is often an issue that could have easily been avoided by regular maintenance. This is why we suggest that you have your uPVC windows checked regularly by our annual maintenance program to reduce the chance of issues.

The majority of modern uPVC windows have espagnolette locks that work by pushing the nose of the handle across a wedge block and then turning the handle to close the lock. They are efficient in locking the window, however if they are not maintained properly, over time they can begin to fail. We recommend that you lubricate them with WD-40 every few times per year.

If you find that your uPVC window isn't opening or closing as smoothly as it used to or when the lock isn't working properly, there may be a problem with the locking gearboxes within the frame. Accessing this can be tricky as it requires the removing of the seals around the frame and removing the handle (be careful not to damage these).

A locksmith who is skilled in UPVC repair will be able diagnose this fault quickly and replace the broken locking mechanism with a precise replacement. This is a quick and simple fix that could save you hundreds of pounds by avoiding the need to buy new windows.