공지사항

UPVC Window Handle Replacement

Replacing a broken window handle is a relatively easy task and, with the right tools, it can be accomplished quite quickly. It is important to identify the kind of handle you have as well as the size of its spindle before you purchase a replacement.

Older uPVC window handles have a spur that extends and is locked over a cockspur wedge striker. They can be left or right-handed and must be to match when replacing.

What kind of lock and handle do I need?

There are a variety of upvc window handles and locks, each with its particular advantages and uses. The type of handle that you own will determine if the locking mechanism you have is effective and if it's easy to open the windows. With time and regular use the upvc handles that are on your windows could become damaged and worn out. This makes them less secure and less effective. In some instances they could even fall off completely. If you notice that your upvc window handles have been removed, it's important to repair them as quickly as possible. This will help prevent burglaries, and keep your house secure.

It's an easy task that anyone can complete. You'll require a few tools, but with the right knowledge, it is a straightforward process that should only take a few minutes. You will need to know the type of handle or lock that you have on your window. This will allow you to choose the correct replacement.

Inline Espagnolette Handles

They are typically located on the side of the window. They are flat and come with an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles have an elongated spindle that runs through middle of the handle into the window frame to operate the latch.

Cockspur Handles

These handles are typically located on older uPVC windows and have a distinctive hook-shaped design. Cockspur handles have one screw that holds the handle to the frame of the window and aren't as secure as other types of window handles.

Handles that can tilt and turn

Unlike the other handles made of upvc, tilt and turn handles can both be rotated to open the windows and the handle can be tilted to the side for ventilation. They typically have a 7mm spindle at the back of the handle. They are available in both left and right-handed versions.

It is important to measure the spindle's size prior to purchasing a new upvc handles. There are a few that are exactly the same size. Drop something into the middle of the hole to test the length. This is the maximum spindle size that will fit into your windows.

What is the spindle?

uPVC window handles operate in a similar way like doors, turning the handle to operate a latch inside the frame. The window can then be opened and shut. The handles can become damaged, especially if often used or are subjected to harsh conditions. This could mean that you have to replace your uPVC windows handles as they may not operate the window properly in the future.

There are a variety of uPVC handles, including Espag, Cockspur, and handle Spaded handles. These handles are designed to fit into the uPVC frames in various ways, and each type of handle utilizes a specific spindle to secure the mechanism into the window. It is crucial to know the type of handle installed on your uPVC windows so that you can replace it with a suitable one.

You can determine the type of uPVC handle you are using by inspecting the base of the handle. There should be a "snap in cover over one screw which holds the handle base in the correct position. Take it off and you should be able to see the second holding screw at the opposite end of the base section of the handle. After both screws have been removed then you should be able to remove the handle from the uPVC.

After removing the uPVC handle, carefully unscrew it from the locking mechanism. Note the length of the spindle. You'll need to buy a replacement double glazed windows of the same length as the handle that was originally used and the locking device.

The main issue with most window handles made of uPVC is that the spindle gets worn out and can no longer work with the locking mechanism. This can be caused by corrosion, damage due to constant use or a loosening locking mechanism. If this happens, you will need to replace both the window handle and the locking mechanism in order to restore the full functionality of your uPVC Windows.

How do I take off the old handle?

Window handles are susceptible to being damaged or broken over time. It is important to repair them as quickly a possible to ensure your safety. It is easy to replace a damaged or worn handle. The task can be completed in under a minute without the need for any special tools.

To take off the handle, you must first remove the screw at the bottom of the handle. Once the screw is removed, the handle can be removed from the base section. Another screw will be located at the base of the handle. This too can be removed. Once both of these screws are removed the handle can be completely detached from the base of the window.

After the handle has been removed, you can take the new handle and align the fixing holes with the holes that are present in the window frame. There might be a small sticker or caps on the new handle, so remove the caps if needed, and then put the handle in the frame. Once the handle is set, it is important to test that it is working by turning the handle, and ensuring that the lock mechanism activates.

Espag handles come with spindles that protrude from the handle and slots into the multipoint locking mechanism on the window frame. Cadenza windows come with an edge with cut-outs which slot into the lock mechanism while Cockspur handles have a long nose that is able to hook over the frame's outer or transom bar cross-member inside the window seal replacement.

Once you have the new handle in place, slide the spindle inside the lock inside the window and then tighten it. Replace the snap-in cover and screw cap (if applicable) after the handle has been firmly fixed. When the handle is in use, simply open and close the window a few times to ensure it works correctly and securely.

How do I install the new handle?

Switching your uPVC window handle isn't difficult and the process is actually very simple. You'll need a screwdriver, and a bit of patience. First, make sure the handle that you are replacing is unlocked. Then, remove any screws that are visible. You could also replace them with screw caps. After removing the handle, you'll need to record the length of spindle that extends from the back. This is crucial as it will determine the type of handle you'll need to buy.

Espagnolette handles that are made of uPVC are the most popular type of handle. They feature a spindle that is connected to the handle, and is responsible for an internal locking mechanism within the frame of the window. The handle opens the latch and allows the window to open. In regular use and over time, espagnolette handles may be damaged.

Cadenza handles are a second type of uPVC window handle commonly used on tilt and turn windows. They have a protruding knife that works with a multiple-point locking mechanism within the window. They are generally more secure than handles made of espagnolette because they are only accessible from the inside. They can be replaced using the same procedure as you would do for handles made of espagnolette however, make sure that the new handle is angled, not flat.

Once you have selected the correct handle, simply align the new handle with the existing screw holes before fixing it with screws. Then, you should put the screw covers on and test the new handle. This is done by moving the handle from the locked position to the unlocked and vice versa several times. If you experience any issues, it might be worthwhile contacting a professional to see if they can help resolve the problem. They can offer advice on how to fix the issue in a timely and effective way.