공지사항

UPVC Replacement Door Handles

Over time, the handles on your doors will wear down and will require replacement. When replacing them, it is essential that the new handles are in line with the dimensions of the handle that was previously used.

The top screw position as well as the lever and keyhole sizes are the three measurements that you need to determine. Use the size guide to assist you.

Inline Lever/Lever

A lever or lever door handle is a modern handle that can be put in on new or replacement doors. This kind of handle is available in many styles and finishes. A number of manufacturers make this type of handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles of uPVC/Composite are constructed from robust materials, and are ideal for multi-point lock doors that require a strong design. The replace window handles are inline and work off the same spindle and screw fixings, so they can be easily incorporated into doors made of uPVC/Composite, either new or old.

The handle can be adjusted and angled to accommodate all users. The handle has been tested for endurance up to 200,000 cycles. This helps to ensure the quality of the finish as well as the performance of the handle over time. The lever that is sprung can be reduced to accommodate more locks. This is particularly useful in doors with smaller door frames where the cylinder is located further back. A lever that is shorter is a good choice for doors that have latches that can be opened by a thumb turn inside.

Lever Pad

The lever pad upvc handle differs from the lever handles used on the majority of doors. These handle types are either operated by one spindle, or two spindles inline or offset. They are usually employed on UPVC double glazed door handles glazed doors. They are available in a variety of variations and finishes.

The handles are available in various finishes, including White chrome, and Gold. The finish is BS EN 1670 Grade 5 and is resistant to rust. This gives the handle the best performance and durability for its intended purpose.

All of the UPVC handle lever pad styles are supplied with a spindle and screws that allow them to be put on a new or existing uPVC door. The backplate fixation centres of 211mm allow for a wider handle, which is typically a benefit when replacing an old or damaged multi-point door lock mechanism. The handle levers come with springs, which can solve the issue of handles for doors that slide out of their horizontal position when they are not being used.

When choosing the replacement UPVC handle and spindle it is important to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement may also be called 'handle centres or cylinder centres'. It is important to match the correct handles.

Once you have the correct PZ size you will then need to ensure that the handle lever pads and push pads are a appropriate shape to accommodate the American with Disabilities Act (ADA) approved handles you require for your doors. These are typically round or square with an internal lever and an external push pad.

The majority of UPVC Lever Pads that we offer are sprung. This means they will return to a horizontal position when not in use instead of hanging and possibly sticking in the frame. This stops draughts from entering the home. Also, the majority of UPVC lever pad handles are handed which allows you to place them on either side of the door.

Euro Cylinder

Cylinder locks are typically found on uPVC doors, but they can be utilized on other types of door. They operate with a key to unlock a cylinder case which will reveal pins that can be aligned with the pins inside the lock body, allowing them to turn the cam, thereby opening the door. Euro cylinders are available with up to six pins. External and internal doors require different levels of security.

Choosing the right cylinder is vitally important; this is contingent on how your door and handle are utilized. Doors that are external, for instance should be equipped with higher security cylinders while internal doors can be secured with a standard cylinder. In addition, some cylinders are available with extra features that can improve security further, such as anti-drill or UPVC Replacement Door Handles anti-bump properties.

A euro cylinder needs to be measured correctly to ensure it's the right size for your door. The cylinder must be measured from the screw hole in the center to the ends of the cylinder. This includes the thumb turn, if there is one. It is best to do this while the lock is in place, but in the event that this is not possible, you can take it off to measure. A cylinder that is protruding beyond the handle and escutcheon might be vulnerable to attacks, such as lock snapping, so it is essential that it's not too long.

The design of the latest cylinders has anti-drilling and bump resistance features. These are designed to reduce the chance of attack by forcing cylinders to turn in a new direction. This can to deflect an attack and ensure your door is secure.

Some cylinders are designed to withstand snapping. This is a growing method of attack on cylinders where the break line inside the lock is smashed with a special tool to snap off the front of the cylinder and allow the door to open. This is faster and easier to achieve than opening the door with a multipoint lock and leaves little evidence of a break-in, which can hinder the insurance claim.

Spring Cassette

This spring cassette is found in the base plate of your door handle. It provides a sprung solution to help return your multipoint lock handles back to their normal position after use. In the past, a lot of these types of handle didn't have a spring built into them, and without it they can droop or drop when the locking mechanism is disengaged. This component is the most effective way to fix this problem. It also stops your door from becoming stuck in the closed or open position since they are difficult to close manually.

These spring cassettes were created to be used with a sprung multipoint lock. They are not compatible with handles that aren't sprung, and you will have to cut a hole in your backplate for them to fit. (Please look at the image for a more detailed diagram). These cassettes are a solution for damaged or missing cassettes on the backplate of uPVC door handles. They are sold as one unit. They feature a square cut out that can accommodate an 8mm shaft.

These spring cassettes offer an excellent value solution for the issue of door handles and hinges that are sagging. They are simple to install and can extend the life of your uPVC door. For more information on our wide range of uPVC accessories and spares, you can get in touch with our team. We are always happy to offer expert advice and support you.