공지사항

How to Do a Door Lock Change

Change of the door lock is an easy and inexpensive method to increase your home's security. However, the procedure isn't for everyone. It requires some skill and patience.

The cylinder is contained within the knob body. The cylinder is what identifies the key when it's put into the lock.

Remove the old lock

First, you must remove the lock you have been using for a while. This is a relatively easy procedure, but there are a few points to be aware of. First, make sure that the lock you choose to install is the right size for the door you have. This will ensure that it is secure and doesn't leave a gap at the latch or deadbolt.

After removing the latch plate, you will be required to search for two bolts or screws on the inside of casing which are holding the casing to the lock halves. Unscrew these with a screwdriver, then remove the lock from the door. If you have a mortise lock, there might be a set screw at the base of the handle that binds it to the spindle. Take off the doorknobs by removing the screw using the help of a screwdriver.

Remove the deadbolt and latch plug from the door jamb. Install your new lock. If you're replacing a mortise, you must measure the distance between your lock's case and your door's edge to make sure that the new lock will fit.

It is possible to replace your lock for a variety of reasons, for instance, when you suspect that someone else is holding the key or if you've got an incoming roommate. You could save money if you take the lock off yourself instead of paying a professional. The process is easier than most people think, and it can be completed in a few minutes.

Start by taking the handle and trim from the door. With a flat screwdriver pry off the trim. You should be able twist off the majority of it. In some instances you might be able to take off the handles completely. Then, check the handle for a tiny hole on the inside and insert a straightened paper clip into it. This will activate the release mechanism and allow you to remove the handle from the door. Then, look on the interior side of the lock to find a small tab that you can press using a flat screwdriver. Once the spindle is removed, you can remove the cylinder and the housing.

Selecting a new locking system

You have many options when it comes to selecting the right lock for double glazed door. Consider different types of locks and choose one that is compatible with the style of your door. Think about the backset (the distance between the edge of the door and the center of the hole in the lock) and the cross bore (small hole that runs along the edge of the door frame). Also, be sure to select a lock that is able to accommodate the door's thickness as well as swing.

Most door locks have been assessed by BHMA and the American National Standards Institute to give you an idea of how well they stand up to use and how difficult they are to pick or disable. A grade 3 lock may be ideal for a quiet urban apartment complex, whereas an entry grade lock could stand up to the traffic at a busy retail storefront on a busy street.

Most smart door locks need a digital code to open. If you're worried about hacking, or other security concerns, speak to an expert locksmith.

replace lock on upvc door the cylinder

If the cylinder of your door lock is damaged or broken you can repair it within a matter of minutes with a simple do-it-yourself project. It is important to select the appropriate cylinder and follow all instructions. First, remove the knob or handle, if it is present. Then using a screwdriver unscrew the trim that surrounds the lock cylinder. Once the trim has been removed, it is possible to remove the screws that hold the cylinder in place using the flathead. The cylinder is then gently pulled out of the door.

Make sure you measure the length of the new cylinder prior to putting it in place. Find the distance from the center to the left and right sides of the cylinder using an instrument. Purchase a new cylinder that has the same measurements. This will stop the cylinder from snapping, Replacing a upvc door lock which can occur when the door is kicked out or when the key is stuck inside.

Place the replacement lock for upvc door cylinder inside the door and then turn the key. This will align the cylinder with the carrier that is usually located on the outside of the lock. You can then loosen the set screws which should be only a couple of turns into the head. You will also need to loosen the screw on the edge of the double glazed door locks that fastens the case, should there be one.

After removing the lock cylinder and replacing a upvc door lock (blog post from 24.viromin.com) it with a new lock by slipping the new cylinder into the case and tightening the set screw. You should also reinstall the piece that connects the cylinder with the stem for the lock indicator and this can be done by pulling out three small tabs on the back of the cylinder using needle-nose pliers. Then, you'll be able to attach the remaining smaller bracket to the back of the cylinder. Then, you must install the strike plate and latch plate as well as the retaining ring that is connected to the top of the lock cylinder.

Installing a new lock

If you're replacing an old lock, start by measuring the width of the door. Most locksets for residential use are designed to fit a door thickness of 1 3/8 - 3/4 inch. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need a stronger door kit. This will include longer screws, or an extended spindle extension or tail piece for door knobs.

The majority of locks come with a detailed instruction booklet to guide you through the installation of the new hardware. Be sure to read the instructions thoroughly before beginning the process to make sure that you've followed all of the necessary steps. The guide will also provide you with an idea of the level of skill required to perform the task. It is possible to ask a person who has worked with double glazed window locks for assistance if you are changing locks for the first time.

Before installing the new lock, it's an excellent idea to put cover the openings with tape the old hardware. This will stop the screws from slipping through the holes, and protect any tiles you may have installed. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with the masking strip or gaffer tape. However, you can use any tape you have.

After removing the screws that hold the lock's interior to its exterior, take the lock off immediately. It's crucial to do this quickly to prevent the lock from accidentally closing itself and harming the mechanism.

Install the new latch bolt into the upper cross bore of the new lock, if it has one. Make sure that you put it in the correct place that is usually marked by an illustration on the faceplate. Then, place the latch plate onto the bolt and secure it in place.

Finally, screw in the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it several times to make sure that it is extended all the way through the strike plate and is secure. Follow the instructions included with your electronic smart lock to program it. This requires downloading an application and registering your email address, verifying you identity, and connecting to the wireless network to connect your device.