공지사항

UPVC Replacement Door Handles

The handles on your doors get worn out over time and need to be replaced. In this case, it is important that the new handles match the exact dimensions of the previous handle.

The three measurements to be inspected are the top screw's position the lever and key hole dimensions. Use the size guide to aid you.

Inline Lever/Lever

A lever or lever door handle is a contemporary handle that can be used on replacement or new doors. This type door handle is available in a variety of designs and finishes. This handle is available from several manufacturers, including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The door handles of uPVC/Composite are constructed of durable materials and are perfect for doors with multi-point locks that require a strong design. The handles are inline and work with the same spindle as well as screw fixings, so they are easily installed on doors made of uPVC/Composite, either new or old.

The handle can be adjusted and angled to accommodate the needs of all users. The handle has been endurance tested to 200,000 cycles. This allows for the assurance of the quality of the finish and the performance of the handle over time. The sprung lever is also adjustable to fit a broad range of locks. This is especially useful for doors with narrower frames, where the cylinder is further back. A shortened lever can also be used for doors that have a latch that can be opened by the thumb inside.

Lever Pad

A Lever Pad door replace window handle made of upvc operates differently from lever-type handles found on most doors. The handle can use a single spindle (inline) or independently from each side using two offset or inline spindles (pad). They are usually employed on UPVC doors with double glazing and come in a range of finishes & variations.

The handles are available in various finishes, including White Chrome and Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, thereby giving the handle a high level of durability and performance for its intended use.

All of the UPVC lever pad styles for handles are supplied with a spindle and screws, allowing them to be fitted on any new or existing uPVC door. The backplate fixing centers of 211mm permit a bigger size window handle replacement that can often be a benefit when replacing a faulty or worn multi-point door lock mechanism. The levers for these handles have springs, which eliminate the problem of handles for doors that slide out of their horizontal position when not in use.

It is important to match up the PZ dimensions of both the multipoint lock and the uPVC doors when selecting a replacement UPVC spindle and handle. This measurement is also called 'handle centre' or cylinder centres'. It is important for matching the correct handles.

After you have identified the correct size of PZ, you will need to ensure that the lever and push pads are shaped to match the American with Disabilities Act compliant handles that you need for your door. They are typically round or tessalyons.co.uk square with an internal lever, and an external push pad.

The majority of UPVC Lever Pads we sell are spring-loaded. This means that they will return to a horizontal position when not in use instead of hanging and possibly being stuck in the frame. This keeps draughts out of the building. Also, the majority of UPVC handle lever pad style handles are handed that allows you to put them on either side of the door.

Euro Cylinder

Cylinder locks are usually used on uPVC doors, but can also be found on other types of doors. The cylinder lock operates by a key which unlocks the cylinder case. This reveals pins that can be aligned with those inside the lock and allow them to turn the revolving camera, thereby opening the door. Euro cylinders can be fitted with up to six pins, with internal and external doors usually requiring different levels of security.

The selection of a cylinder is essential. It is based on the type of use your doors and handles will receive. Doors that are external, for instance are required to be fitted with cylinders that are more secure and doors inside can be secured with an ordinary cylinder. Certain cylinders come with extra features that increase security, such as anti drill or anti bump properties.

A euro cylinder must be measured accurately to ensure it's the correct size for your door. The cylinder should be measured from the central screw hole to the ends of the cylinder. This includes the thumb turn, should there be one. It is recommended to do this with the lock in place, but when this isn't possible, you may remove it to take measurements. It is important to ensure that there is no extension of the cylinder beyond the handle or escutcheon. This can make it susceptible to lock snapping attacks.

Most modern cylinders are designed with bump and anti-drill features that are built into their design. They are designed to minimize attack chances by forcing the cylinders to turn in a new direction. This can to deflect attacks and ensure your door is secure.

Certain cylinders are made to resist snapping. This is a typical attack on cylinders. A special tool is used to break the break line of the lock, and the front of the cylinder is snapped off. This is a much faster and easier way to gain access than through a multipoint locking system. It also leaves less evidence of the burglary which can hinder insurance claims.

Spring Cassette

The spring cassette is situated inside the base plate of your door handle. It offers a spring-loaded solution to bring the multipoint lock handles to their resting position after use. In the past, a lot of handles of this kind didn't have a spring built into them and without this they tend to droop or drop once the locking mechanism is disengaged. The addition of this simple element is one of the most effective ways to fix this, and is an excellent way to stop your doors made of upvc from becoming stuck in the open or closed position, as they aren't always simple to close manually.

These spring cassettes were designed to be used with sprung multipoint lock. They won't work with handles that are not sprung and you'll have to cut a hole into the backplate to allow them to fit. (Please check the image for a technical diagram). These cassettes are a replacement to damaged or missing cassettes that are in the backplate of uPVC door handles. They are supplied in one unit. They feature a square cut out that accommodates an 8mm shaft.

These spring cassettes provide a great value solution to the issue of door handle replacement handles that have become sagging. They are simple to put in and will extend the life span of your uPVC doors. Please contact our team for more information on our wide range of uPVC accessories and [Redirect-Java] spares. We are always happy to offer professional advice and assistance you.