공지사항

Electricity Meter Installation

An electric meter is an excellent method of keeping track your electricity consumption. They can also help you cut your energy bills!

They are typically a transparent metering device encased in glass that resembles the shape of a mason-jar. They have five dials , as well as a large rotating meter that measures kilowatt hours of electricity.

The Feeder Side

The most crucial component of the installation of an electricity meter for homeowners is the feeder. This is because it is connected to the complete electrical service. This is the part where the utility company's feed connects the meter and the wires connect to your home's electrical installation inspection system. It's also where you'll discover the most obvious wire connections: neutral, hot and ground. The best part is the utility company usually provides the meter and the necessary wiring, but the process of putting it all together is up to you.

To construct the best base for your meter, you'll require some of the above items as well as an ample amount of anti-corrosion compound to shield your wires from damage by the elements. First consider the orientation of the meter (left or right-hand front) and then determine the lengths of the three wires you intend to attach to it. A measuring tape with telescoping capabilities is the ideal tool for this. Be sure to wear gloves.

The Load Side

The load side of an electricity meter installation is where the electrical feed departs the meter and goes to the main service panel. The feed could come from a single or multiple circuit breakers located in the main panel. The connection for the load is typically made at the bottom two load terminals on the hot bus bars on the meter however this can be accomplished with an interim disconnect (See Figure 3).

The wiring connecting the service wires to meter must be in conduit and must be placed in a spot that is not blocked by furniture or other obstructions. It should be at least two feet (2') from any exposed wiring on the side that is connected to the load and connected to the meter base with an entry cap on top of the conduit (see figure 16).

Unless LES approves a better method wires should not be run in conduit. The conduit should be accessible to Company representatives for meter reading and testing.

The base of the meter should be securely fixed to the brick's studs or concrete block or the equivalent. A backing of 3/4-inch thick outdoor plywood is required when the meter is intended to mount on metal, vinyl or wood lap siding. It should be placed on a level surface and straight. It should also be set in a position where it is easily accessible to Company representatives for reading the meter as well as testing and maintenance.

Grounding Wire

The installation of electricity meters includes an earthing wire to safeguard the home from the effects of excess electricity. If a short circuit or excess electric current is detected and the grounding wire is damaged, it can help to safely discharge the power from the house and keep it from returning to the mains.

One of two ways the grounding wire connects to the earth outside your home is by using a copper water pipe or an 8-foot long ground rod. It could be connected to the copper water pipe or an 8-foot long rod for outdoor grounding that is driven into the soil.

If the grounding wire doesn't work correctly, excessive electricity could get through other channels to your home. This can cause damage to electronics and appliances, or even the possibility of a fire in your home. It's essential to understand the causes of these issues and what you can do to avoid them.

A simple method to determine whether your outlets are grounded or not is to look at the prongs. Ground outlets have three slots, while ungrounded ones only have two. The ground wire is the one that is connected to the d-shaped slot beneath the parallel slots.

Currents of electricity are attracted by the solid mass of the earth below your feet because it has an electric charge that is negative. Ground wires are designed to let these positive charges locate a safe location so that they don't get energized, which can cause problems.

If you don't have an electric meter installed, or it's been several years since the meters were replaced or repaired then you should contact your utility provider to find out whether it's properly grounded. To ensure it is working correctly an electrician with a license should examine the meter.

When choosing an electrician to install your new meters, outdoor make sure you are aware of the rules and regulations that your local utility company has enacted. They are responsible for protecting your home from over-voltages and keeping your family safe.

They must connect the ground wire to base of meter and ensure all metal casings that hold electrical loads are bonded with system neutral. If there's an electrical installations near me fault on the hot or neutral wires, they can become energized and touch the metal casings, tripping the breaker. This is a potentially dangerous scenario that could cause an electrical installation companies shock or death.

The Meter Mechanism

The Meter Mechanism is an important element of an electric meter installation. It measures the actual electricity consumption. It can be found on a utility pole or in a box.

The metering mechanism in an electric meter usually a disc made from aluminum which rotates in response to changes in the magnetic fields of the coil due to current and voltage. It spins at a pace proportional to the amount of electricity consumed.

A meter disc is typically supported by a spindle that has gears attached to it. The gears rotate and display the energy utilized by series dial in kilowatt hours (kWh).

An electricity meter has three primary components comprising the disc, the mechanism for the disc, and finally, an LCD. The disc is the primary element of the meter because it determines the amount of electricity consumed and the total number of kWh.

For a precise reading, the meter should be calibrated to a standard. This procedure is typically carried out in a testing laboratory. During this process the circuit of the meter is checked to ensure that it's not under- or over-volting the power level.

After the meter has been correctly calibrated, it is able to be placed in a box. It is connected to an incoming voltage reference ground wire, a ground wire, and a grounding cable that runs through the meter box until a grounding rod buried under the ground.

In certain situations meters can export power to the grid in addition to its consumption. In these cases the meter can run in reverse during periods of net export and decrease the customer's total recorded energy consumption. This can result in the customer getting credit for the energy that is pumped out of the meter to the grid, even if it is less than the amount actually consumed by the meter.

In order to ensure that the meter operates properly, the technician has to connect the line and load wires to the terminals on the neutral bus bar in the middle of the meter box. These wires are usually marked with white tape to signal that they are neutral. Once the wires have been properly spliced, they will be secured by being tightened.