공지사항

Electricity Meter Installation

An electric meter is an excellent method of keeping track of the amount of electricity you use. They can also help reduce your power bills!

They are usually a clear glass-encased metering device that resembles a mason jar. They have five dials , as well as a large rotating meter that measures kilowatt hours of electricity.

The Feeder Side

The most important component of an electricity meter installation for homeowners is the feeder. This is because it connects to the whole electrical installation prices service. This is the part where the utility company's feed connects to the meter as well as the wires that go to the electrical installation companies near me system in your home. It's also where you'll discover the most obvious wire connections: hot, neutral and ground. The good thing is that the utility company will usually provide the meter and wiring. However, you're the one who installs electric meters puts it all together.

You'll need to construct the highest quality base of the meter. The most important thing you need to do is figure out the meter's direction (left or right hand front) and then take a measurement of the length of the three wires you intend to connect to it. The most effective method for doing this is to utilize a telescoping measuring device, and don't forget to put on a pair of gloves.

The Load Side

The load side of an installation electricity meter is where the incoming electric feed leaves the meter and then enters the main service panel. This feed could come from an individual breaker or multiple circuit breakers located in the main panel. The load connection is typically placed at the lower two load terminals on the hot bus bars on the meter however this can be accomplished using an interim disconnect (See Figure 3).

The conduit that runs from the service wires to meter must be in conduit. It must be located in a position where it isn't blocked by furniture or other obstructions. It must be at minimum two feet (2') from any exposed wiring on the side of the meter that is loaded and must be connected to the meter base with an entrance cap on top of the conduit (see figure 16).

If the wires aren't in conduit, then they should be routed in a weatherproof conduit, unless LES approves a different method. The conduit should be accessible to Company representatives to conduct meter readings and tests.

The base of the meter has to be securely fixed to the block studs of concrete or brick. A backing of 3/4-inch thick outdoor plywood is required if the meter is to be mounted on vinyl, metal, or wood lap siding. It should be installed in a level and plumb. It should be located in a place where it is easy for Company representatives to read, test and electrical domestic installation maintain the meters.

Grounding Wire

A grounding wire is included in electricity meters to protect your home from excessive electricity. Grounding wires are used to cut off power to the house in the event of a short circuit or excessive electricity.

One of the ways that the grounding wire connects to the earth outside your home is to use copper water pipes or an 8-foot long ground rod. It can be connected to a copper waterpipe or an 8-foot long ground rod that is inserted into the soil.

When the grounding wire isn't grounded, excessive electrical current can escape through other pathways into your home damaging appliances and electronics , or an eventual house fire. It is essential to know what these issues are to avoid them.

An easy way to tell whether your outlets are grounded or not is by looking at the prongs. Outlets that are grounded have three slots while unground outlets only have two. The d-shaped slot just below the parallel slots is the one which is connected to your ground wire.

Currents of electricity are attracted by the solid mass of earth beneath your feet because it has an electrical domestic installation charge that is negative. Ground wires are designed to assist these positive charges find a safe location to go so they don't become energized and cause problem.

If you don't have an electric meter installed or it's been some time since the meter was repaired or replaced and you're in need of assistance, contact your utility provider to determine if it has been grounded correctly. To make sure it's working correctly, a licensed electrician must inspect the meter.

If you're considering an electrician to install your new meter remember that they must follow the rules and regulations established by the local utility company. They're accountable for protecting your home from excessive voltages and keeping your family safe.

They must connect the ground wire to the the base of the meter and ensure that all metal casings that hold electrical loads are bonded with system neutral. If the hot or neutral wires are energized it could trigger the breaker. This could lead to an industrial electrical installation shock or even death.

The Meter Mechanism

The Meter Mechanism is an essential element of an electric meter installation. It measures the actual electricity consumption. It is located on a utility pole, in a meter box, or in the premises next to the consumer unit or distribution board.

The metering mechanism of an electric meter is typically a disc made from aluminum that rotates according to changes in the magnetic fields of the coil caused by current and voltage. It spins at a speed proportional to the amount of energy consumed.

A meter disc is typically supported by a spinning device that has gears attached to it. The gears rotate a register that shows the energy utilized by series dial in kilowatts (kWh).

An electricity meter has three main components comprising the disc, the mechanism of the disc, and an LCD. The disc is the most crucial element of the meter because it determines both the amount of power consumed and the total number of kWh.

The meter should be calibrated in accordance with a standard in order to get an accurate reading. This procedure is typically carried out in a test laboratory. During this process the circuit of the meter is checked to make sure that it's not over or under-volting the power level.

Once the meter is properly calibrated, it can be placed in a box. It is connected to the reference high voltage installation grounded wire, as well as a grounding wire that runs through the meter box until a grounding rod buried under the ground.

Sometimes, a meter can export power to the grid in addition to its consumption. In these instances the meter will operate backwards during times that are net exports and reduce the total energy consumption. This will result in the customer being credited with the energy that flows out of the meter into the grid even if it's less than what's actually consumed at the meter.

The technician must connect the line and load cables to the terminals on the neutral bus bar located in the middle of the meter box . This will ensure that the meter runs properly. The wires are usually marked with white tape in order to identify them as neutral. Once the wires have been properly spliced, they will be secured by being tightened.