공지사항

UPVC Window Repairs

Upvc windows can cut heating costs and are energy efficient. However, as they age, issues can develop that require repair. This could include damaged hinges, handles or locks.

DIY enthusiasts can repair wooden windows relatively easily. It can be cheaper than purchasing a new window.

Cracks

Cracks and fractures can be a major issue. Windows that are not repaired can lead to water intrusion and less effective barriers to cold weather, or even structural damage. Find an expert local builder that specializes in the repair of uPVC frames. They must have the required skills, experience and equipment to ensure the best results. This will ensure that your crack is repaired swiftly before it gets worse and you don't need to replace your window unit or glass.

Small cracks in glass can be fixed by using a variety of DIY solutions. Super glue and masking tape are among the most commonly used products that can hold broken glass in place for a few minutes. For deeper cracks, tape might need to be extended on both sides.

Another option is two-part epoxy that can be used to repair broken or cracked glass. It's available at a lot of hardware stores and can be purchased for about $10. Ensure that your workspace is prepared prior to mixing the epoxy. Make sure you have the right equipment for the job, such as a soldering iron.

If your upper or lower sash is hard to raise it's most likely because the cords that connect the sash weights are damaged. This is an easy fix that can be done with a ladder and a flathead screwdriver. A damaged dripcap can be easily repaired at home. Drain caps that are free of rot are readily available at many home centers and can be nailed and put in place using caulk. Make sure that the glass of double glazed window repairs or triple-paned window is not broken. This is due to the gases that fill the space between the panes contribute to improving energy efficiency and should be kept, not escaping.

Water Leaks

If your uPVC window is leaking, it can cause damage to your home and result in costly repairs. Water leaks can also cause structural damage to your home and mold growth. To avoid the damage, it's essential to fix any problems caused by windows that leak as soon as possible.

A damaged sealant around window frames is a typical reason for leaks. Silicone caulking will restore the seal to its original state and prevent leakage. Look for gaps and cracks around the window frame, as well as the stone or brick wall surrounding your windows.

A blocked drainage hole or defective flashing are also typical causes of windows that leak. Make sure that the drainage holes have not been blocked or blocked, particularly after a heavy downpour. It's also recommended to examine the flashing around the top of your window and ensure that it's sealed properly.

It's also important to make sure that your drip cap doesn't have any rot or is missing. A drip cap that is rotten or one that's not there will allow water from above to seep into your window and cause structural damage. Replacing a drip cap isn't a complicated job and generally a simple process of buying an entirely new one and nailing it into the right spot.

A professional can also check your windows for watertightness. They can use a special tool to measure the water-tightness and strength of your windows and ensure they meet the industry standards. If your windows fail the test, they'll have to be replaced. This is a cost-effective repair but it's worth it for the security and safety of your family.

Sagging

If your windows do not close properly, it can cause a variety of problems, including condensation, drafts and a rise in your energy bills. It could be an indication that the windows weren't well fitted when they were installed or that the sealant is no longer effective. There are a few things you can do to solve the issue.

The first step is to prepare a workspace in a room with plenty of natural light to fix your window in a timely manner. Begin by laying down newspapers or an old blanket to protect the flooring from any splinters and drips from the windows while you work.

You should also make use of a white cloth that has been soaked in a solution of detergent and water. This will ensure that you don't leave any color stains on your windows. Mark the location of the hinge channel on your uPVC window when you are ready to begin working. Unscrew the channel, and then fill the screw holes in the frame using epoxy (for uPVC frames) or wood filler. Make sure you scrape the hole you have filled before it sets.

Install the hinge channel once the holes have been filled. Be sure to center it on the window jamb and then drill the new screw holes approximately a quarter-inch from the original locations.

Next, measure the length of the spindle protruding from the underside of your handle and then order a replacement online or bring your old one in to the hardware store to purchase a new. Then, take the setscrew off the operator shaft. Flatten it to allow the set screw to lock onto the shaft. Now, your uPVC windows should close without a hitch.

Broken Hinges

If your uPVC window hinges have been damaged or are not functioning correctly, you will find it difficult to open or close the window. This can be a security issue and could also hinder your home from staying warm or cold. It's simple to find a new hinge for your uPVC windows. But, it's crucial to ensure that you have the right type of hinge for your windows.

This is because the hinges need to be of the same width to fit into the window frame. The most commonly used hinge used in windows made of uPVC is an 15mm or 18mm UPVC window hinge. There are also specialised hinges for wooden frames. The right type of hinge will allow you to avoid common problems with your windows.

There are several reasons why your window hinges may have become stiff or loose. The hinges may not be tightened enough. To test this, take an electric screwdriver to locate the friction screw at the hinge's end. Loosen it. Then, you can adjust it by turning it either way.

Contact Preston Glass Fix if your UPVC window's hinges don't work correctly. We can provide an immediate solution. Our technicians will examine the condition of your hinges, and give you advice on the best solution. We can replace the window hinges, re-tension them, or install new locking mechanisms to ensure that your UPVC windows are secure and safe for years to come.

The locks are not working properly

UPVC window mechanisms and locks are an important part of security for your home. They make it difficult to open windows without breaking into the house. If a lock fails, it can be a frustrating experience, but it's an simple fix and you don't need to replace the entire window.

Often the problem can be a minor issue that could have been avoided by regular maintenance. This is the reason we recommend having your uPVC windows maintained regularly using our yearly maintenance package to reduce the chance of problems.

Modern uPVC windows come with espagnolette locks. They work by pushing the nose end of the handle onto the block with a wedge, and then turning it to close the lock. They are effective in locking the window, however should they not be maintained correctly, over time they could begin to fail. We recommend that you lubricate them with WD-40 every few times per year.

If you notice that your uPVC windows don't open and close as smoothly as they used to or when the lock isn't functioning properly, it is likely that there is a problem with the gearbox that locks the window frame. The process of removing this gearbox can be difficult as it requires the removing of the seals around the frame and the removal of the handle (be cautious not to damage these).

A locksmith who specializes in UPVC repairs is able to identify the problem quickly and then be able to repair the failed locking gearbox with an exact replacement. This quick and simple fix can save you hundreds of dollars by not having to purchase new windows.